Aruba switch allow unsupported transceiver. allow-unsupported-transceiver.

 

Aruba switch allow unsupported transceiver. i have a sfp to rj45 from fs. 0016 03-Aug-2021 10-Aug-2021. 00km (SMF), 30m (OM1), 80m (OM2), 300m (OM3) Diagnostic Support : None Vendor name : SOURCEPHOTONICS Vendor Part Number The Allow Unsupported Transceiver feature allows the user to try a transceiver part (including DAC cables) without the switch attempting to authenticate it as a genuine HPE Aruba part. The allow-unsupported-transceiver command is an undocumented feature. This was never an issue with the 1Gb ports, but as soon as you tried to go 10Gb it wanted to verify the transeiver. If there are any non-Aruba transceivers already inserted, remove and reinsert them. The term "third-party transceiver" applies to Allowing unsupported transceivers enables the Aruba Switch to unblock the port and allow third-party transceivers to connect to the switch. Jan 13, 2021 · Expanded list of Aruba Switches supporting 10G HPE Compute DAC cables. Description. Solution: The 16. what could be the problem please and how to resolve it? Thank you in advance Mar 18, 2017 · "This feature enables and disables the use of non-HPE Aruba transceivers on HPE Aruba switches. 3 and I try to enable third-party transceivers with command : " . allow-unsupported-transceiver. This undocumented feature was included in releases numbered 16. Not all unsupported products can be recognized and enabled; they may be unable to be Showing allowed unsupported transceivers: switch# show allow-unsupported-transceiver Allow unsupported transceivers : yes Logging interval : 1440 minutes ----- Port Type Status ----- 1/1/31 SFP-SX unsupported-allowed 1/1/32 SFP-1G-BXD unsupported-allowed 1/1/2 SFP28DAC3 unsupported Feb 15, 2019 · We are installing new VSX stack based on Aruba 8230 with TL. May 7, 2020 · Aruba-3810M-16SFPP-2-slot Transceiver shows J4859D unsupported SFP. 16. To enable this feature, complete the following procedure in Aruba Central: When I enable unsupported transceiver support and look at the details, this is what I see: Transceiver in 1/1/1 Interface Name : 1/1/1 Type : SFP+SR (unsupported) Connector Type : LC Wavelength : 850nm Transfer Distance : 0. Sep 21, 2020 · Hi @Onitsuka !. An HPE pluggable module that is supported in this interface" My firmware version is PL. Mar 4, 2020 · Hopefully Aruba will update their transceiver guide documentation soon to include the 6300 / 6400 / 8325 platforms to this level of detail as this can have a large financial impact on refresh projects for customers especially as CX doesn't allow "unsupported 3rd party optics" so delivering news that only 1 or two specific transceivers are AOS-Switch es running software versions 16. Jan 3, 2023 · These switches only allow original SFP+ modules, unless you use the allow unsupported transceivers which voids warranty. This feature is not available on any other ArubaOS-Switch switches. Aruba-2930F-8G-PoEP-2SFPP(config)# allow-unsupported-transceiver Warning: The use of third-party transceivers is at your own risk and may void support and warranty. Product Line Manager, Switching , Transceivers, Accessories, Power, and other things Roseville CA, USA----- switch# show allow-unsupported-transceiver Allow unsupported transceivers : yes Logging interval : 1440 minutes ----- Port Type Status ----- 1/1/31 SFP-SX unsupported-allowed 1/1/32 SFP-1G-BXD unsupported-allowed 1/1/2 SFP28DAC3 unsupported Sep 7, 2021 · Hi Koen, that's pretty strange since an original J9151E SFP+ LR Transceiver is supported on Aruba 2930F (for models having SFP+ ports) and the J9151E type replaced the corresponding J9151D type during 2019 IIRC so the E type is well mature. Only 1G and 10G transceivers are enabled by this command and unsupported transceivers of other speeds will remain disabled. Allowing use of unsupported products in Aruba switches can assist in the initial installation or validation of switching products while you obtain fully supported products. The "allow-unsupported-transceiver" ("UT-mode") feature provides the flexibility to use non-Aruba/HPE transceiver products. Consult your Aruba Sales team for alternative solutions. 02. switch(config)# no allow-unsupported-transceiver confirm Warning: Unsupported transceivers, DACs, and AOCs will be disabled, which could impact network connectivity. 000 newest this time and try again but I cann't allow too. Aug 13, 2019 · I've been following the steps in the ArubaOS-Switch Unsupported Transceiver Guide V2 and every command except allow-unsupported-transceiver has been working as expected. HP Aruba switches require only one configuration parameter in order to use third party SFP and SFP+ modules. The J9142B/J9143B were End of Sale in April 2016 and are no longer available. 5. Please find firmware link, the latest . HP Aruba Switches . Adds information about HPE Server DACs that have been tested against the Apr 12, 2018 · HPE FlexNetwork Transceivers are n ot supported, but from CX 10. Have you thought about using this one? The Allow Unsupported Transceiver feature allows the user to try a transceiver part (including DAC cables) without the switch attempting to authenticate it as a genuine HPE Aruba part. Showing allowed unsupported transceivers: switch# show allow-unsupported-transceiver Allow unsupported transceivers : yes Logging interval : 1440 minutes ----- Port Type Status ----- 1/1/31 SFP-SX unsupported-allowed 1/1/32 SFP-1G-BXD unsupported-allowed 1/1/2 SFP28DAC3 unsupported Transceivers originally designated for use in Aruba WLAN controllers or former Mobility Access Switch (MAS) products End-of-life Aruba Transceivers The unsupported transceiver mode (UT-mode) is designed to allow the possible use of these unsupported products. The allow-unsupported-transceiver command is only available on the 3810M, 5400R, 2920, 2930F, 2930M, 2540, and 2530 switches. 10. Allow-Unsupported-Transceiver feature enabled: Platforms KB, WB, WC, YA, YB, YC Category Ports Severity Information Description Unsupported Transceivers found in: <EVENT_MSG> List of Non-HPN transceiver has been present into the switch. Mar 19, 2019 · Unsupported Transceivers The use of unsupported transceivers is allowed on certain ArubaOS-Switch models using this command (for at least some transceivers, a reboot may be required): allow-unsupported-transceiver switch(config)# show allow-unsupported-transceiver Allow unsupported transceivers : refer to the Fundamentals Guide for your switch model. Older J9142B/J9143B transceiver may work in switches using the "allow-unsupported-transceiver" feature. Showing detailed transceiver information with identification of unsupported transceivers: switch# show interface transceiver detail Transceiver in 1/1/2 Interface Name : 1/1/2 Type : SFP+ER (unsupported) Connector Type : LC Wavelength : 3590nm Transfer Distance : 80m (SMF), 0m (OM1), 0m (OM2), 0m (OM3) Diagnostic Support : DOM Vendor Name Jul 7, 2023 · For CX, this is enabled by default. With this new command, the admin can override this behavior. It doesn’t support that command. 3rd Party transceiver before added check the transceiver compatibility matrix switch(config)# no allow-unsupported-transceiver confirm Warning: Unsupported transceivers, DACs, and AOCs will be disabled, which could impact network connectivity. log-interval Configure unsupported transceiver logging <cr> AOS-CX(config)# allow-unsupported-transceiver the allow unsupported transceiver command does not work Im trying to get set up my new switch and cant get the sfp to work. 02)? it is described here and here (just two examples) or in the official Aruba 5400R zl2 documentation (any software from 16. Jul 7, 2023 · For CX, this is enabled by default. Please see HPE Warranty terms and conditions. This is the default. Craig Syme May 07, 2020 06:20 AM Its an orderable part for that switch, what does the output of 'show tech transceivers' and also 'show switch# show allow-unsupported-transceiver Allow unsupported transceivers : yes Logging interval : 1440 minutes ----- Port Type Status ----- 1/1/31 SFP-SX unsupported-allowed 1/1/32 SFP-1G-BXD unsupported-allowed 1/1/2 SFP28DAC3 unsupported We found the old 1 Foot DACs that shipped with the MAS switches worked with the allow-unsupported-transceiver on 2930F switchs with serial numbers in the CN69 range, started to experience light errors on switches with serial numbers in the CN6B range, and would not even consistently come up and were heavily errored on switches with serial numbers in the CN76/CN77 range. Feb 9, 2021 · On the HP enter the command " allow-unsupported-transceiver" and on the dell switch " allow unsupported-transceiver" to enable third party transceivers. The information presented here is for compatibility use. Not all unsupported products can be recognized and enabled; they may be unable to be Transceivers originally designated for use in Aruba WLAN controllers or former Mobility Access Switch (MAS) products End-of-life Aruba Transceivers The unsupported transceiver mode (UT-mode) is designed to allow the possible use of these unsupported products. Have a look into this. That may be why the menu does not show any ports. The output of show modules just shows the module with two SFP+ slots, which seem not to have any (supported) SFP+ modules plugged in. I've got a number of 2930F switches, running software revision WC. I’ve ran into other vendors that have similar commands. For more information, see Opening Remote Console for Switch. Insert a non-HP Aruba transceiver into the switch and check the transceiver list using the show tech transceivers command. Nov 14, 2019 · When I got a new J9773A Switch, it in version YA. com coded for h3c and a mellanox coded dac cable. switch(config)# allow-unsupported-transceiver Warning: The use of unsupported transceivers, DACs, and AOCs is at your own risk and may void support and warranty. Use 'show allow unsupported-transceiver' to identify unsupported transceivers, DACs, and AOCs. The same cascade is working between Aruba and another SMC switch. The unsupported message can be seen in switch output like: Aug 12, 2022 · Have you tried the allow-unsupported-transceiver way (available since ArubaOS-Switch 16. 0013 or later, support the use of third-party transceivers. 2. 03. The no form of this command disallows using unsupported transceivers. 11) freely available on ASP (Aruba Support Portal) here. If the transceiver is recognized, the support has been enabled. In fact, we can run the fiber to the Dell, then run Ethernet from the Dell to the Aruba and everything works. Transceivers originally designated for use in Aruba WLAN controllers or former Mobility Access Switch (MAS) products End-of-life Aruba Transceivers The unsupported transceiver mode (UT-mode) is designed to allow the possible use of these unsupported products. For AOSS, this must be enabled with the command allow-unsupported-transceiver. -----Herman Robers Jul 12, 2019 · "The Allow Unsupported Transceiver feature allows the user to try a transceiver part (including DAC cables) without the switch attempting to authenticate it as a genuine HPE Aruba part. Nov 15, 2016 · Enable the use of unsupported transceivers and read the message 🙂; Aruba-2930F-8G-PoEP-2SFPP(config)# allow-unsupported-transceiver Warning: The use of third-party transceivers is at your own risk and may void support and warranty. Now, you can use any brand of SFP and SFP+ modules. Nov 30, 2022 · I 12/01/22 10:04:53 03704 ports: ST2-CMDR: Allow-Unsupported-Transceiver feature enabled: Unsupported Transceivers found in: 2/C12-2/C16,2/K1-2/K2 especially considering that 2/K1 and 2/K2 (so VSF Member 2 interfaces K1 and K2) are interfaces used for setup the inter-switch VSF Links at 40Gbps. To enable this feature, complete the following procedure in HPE Aruba Networking Central: Nov 28, 2023 · This feature enables and disables the use of non-HPE Aruba transceivers on HPE Aruba switches. Obviously, we need the fiber and SFP transceiver to work in the Aruba. Previously, the switches were simply blocking the use of 3th party transceivers. 0001 and having issues with unsupported tranceivers which is annoying. Was just going to suggest this. You can read more on how to use this command on our allow unsupported transceiver Aruba knowledge base article. . 0005, so unless this feature has been deprecated I believe our configuration is compatible. Showing allowed unsupported transceivers: switch# show allow-unsupported-transceiver Allow unsupported transceivers : yes Logging interval : 1440 minutes ----- Port Type Status ----- 1/1/31 SFP-SX unsupported-allowed 1/1/32 SFP-1G-BXD unsupported-allowed 1/1/2 SFP28DAC3 unsupported Showing allowed unsupported transceivers: switch# show allow-unsupported-transceiver Allow unsupported transceivers : yes Logging interval : 1440 minutes ----- Port Type Status ----- 1/1/31 SFP-SX unsupported-allowed 1/1/32 SFP-1G-BXD unsupported-allowed 1/1/2 SFP28DAC3 unsupported Jul 10, 2024 · Allow third-party transceivers: Use allow-unsupported-transceiver CLI command to enable 1G and 10G third-party optics (thats including DAC and AOC cables). Nov 5, 2023 · Hi Pastor, This is an enhancement done as part of 2. In configuration mode, run the following command: allow-unsupported-transceiver confirm. The problem is that the SFP port is up ( the led with green color) on the Fortiswitch side but in Aruba is down (no led). This transceiver obviously doesn't work in the Aruba, but it does work in the Dell. Not all unsupported products can be recognized and enabled; they may be unable to be Aug 8, 2021 · We're moving from an old Dell switch with a Dell transceiver - 0GF76J. Allowing unsupported transceivers enables the AOS-Switch to unblock the port and allow third-party transceivers to connect to the switch. One of the new Central 2. I found out the problem is, my 8200 is too damn old. AOS-CX(config)# allow-unsupported-transceiver. Feb 16, 2020 · service unsupported-transceiver no errdisable detect cause gbic-invalid. For example we have some SPF+ DAC cable from Lenovo and try to connect it to anothe HP 5500 chasis. Allows unsupported transceivers to be enabled or establish connections. Unsupported transceivers Option. 9 SW release blog and user guides are available in the below link Sep 26, 2022 · (BTW: the new 9300-32D switch and new 400G xcvrs and AOCs and 200G AOCs will be covered in the upcoming Edition 13 -- ETA End of October, 2022)-----Ed Kurata, Aruba Sr. 9 SW to highlight if the transceiver is supported or unsupported. 7 features allows the user to enable/disable the unsupported transceivers (third-party transceivers) from within the GUI for AOSS devices. I have another device (a custom built machine) that works with this transceiver and cable. It is only available on the 3810M, 5400R, 2920, 2930F, 2930M, 2540, and 2530. Jan 4, 2024 · Verify whether ‘allow unsupported transceiver’ has been enabled. I did try a few things (some out of desperation): reboot the switch; allow unsupported transceiver switch(config)# allow-unsupported-transceiver Warning: The use of unsupported transceivers, DACs, and AOCs is at your own risk and may void support and warranty. Not all unsupported products can be recognized and enabled; they may be unable to be Mar 19, 2019 · Unblock the port when 3rd party transceivers are used on Aruba HPE switches. 1000. Command History. 02 release for the Aruba HPE switches includes a new feature to enable the use of unsupported transceivers. To enable this feature, complete the following procedure in Aruba Central: Open the console of the switch using the console option in Aruba Central. There is no guarantee that all third-party transceivers will work: typically the ones that work are industry-standard types as identified by the MSA standards body. but It not have this command, so I try to upgrade version to YA. The Aruba SFP is 1 GB and also for the Fortiswitch. Aug 12, 2021 · As mentioned J9851A, 1. AFAIK, the "allow unsupported-transceiver" command is an undocumented feature. Allowing the use of unsupported products in Aruba switches can assist in the initial installation or AOS-S switches running software versions 16. 5 release we support allow-third party transceivers. Apr 19, 2024 · " Transceiver 10G-LR inserted in 1/1/26 is supported. There is no guarantee that all thirdparty transceivers will work : typically the ones that work are industry-standard types as identified by the MSA standards body. KB. 0013 and later. The Allow Unsupported Transceiver feature allows the user to try a transceiver part (including DAC cables) without the switch attempting to authenticate it as a genuine HPE Aruba part. confirm Automatically acknowledge warning and skip confirmation prompt. There is no guarantee that all third- Allow-Unsupported-Transceiver feature enabled: Platforms KB, WB, WC, YA, YB, YC Category Ports Severity Information Description Unsupported Transceivers found in: <EVENT_MSG> List of Non-HPN transceiver has been present into the switch. The term transceiver applies collectively to optical transceivers, DAC and AOC cables, and port adapters. Not all unsupported products can be recognized and enabled; they may be unable to be Jan 5, 2021 · To my recollection we had to buy different transceivers for 5406Zl switch. My Networking | HPE® Official Site. 12. Allowing unsupported transceivers enables the AOS-S to unblock the port and allow third-party transceivers to connect to the switch. Unsupported transceiver mode. The allow-unsupported-transceiver (UT-mode) command allows usage of non-Aruba/HPE transceiver products. Edition 7, published March 2020 Adds information about 25G products (Xcvrs, DACs and AOCs) along with 40G AOCs Now lists supported transceivers and DACs for the Aruba 6300 and 6400 CX switch series. On HP side the tranceiver is recognized and there is warning but it works. 02 up to 16. Your link showed a “generic” SFP+ transceiver for the Aruba switch. fdly clbr lkcu onipoi bjb icgnoayvf ttkco mwmrpb pvlf fjthla